Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D Which Cisco IOS command is used to advertise a default route into an OSPF domain regardless of whether a default static route is configured? A. default-information originate B. default-information originate always C. default-information originate permanent D. default-information originate no-check Identify the true statements about VLANs and trunking with IEEE 802.1Q. (Choose three) A. The native VLAN should be changed from the default for security B. The layer 2 header must be adjusted to keep track of VLAN origins C. All VLANs have a tag D. Inter Switch Link and IEEE 802.1 Q are trunking protocols E. Access ports carry traffic for multiple VLANs https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html You are configuring port security on a Catalyst IOS switch. You need to choose a violation mode that will deny frames that are in violation of the port security settings while still allowing frames that are not in violation. In addition, syslog messages need to be generated and the port security violation counter must increase each time a violation occurs. Which port security violation mode should you choose? A. Err-disable B. Protect C. Shutdown D. Disable E. Restrict Which Cisco IOS router prompt indicates that you are in Global Configuration mode? A. Router# B. Router(config-if)# C. Router. D. Router> E. Router(config)# Routing tables can be populated in a number of different ways. Which of the following describes the directly connected route type. A. Router attached to this network B. The router interface has a local IP address C. A system administrator manually enters static routes directly into the configuration D. Learned by exchanging routing information E. Used when no explicit route to a destination is found https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/identification-of-the-path.html Please choose the correct sequence of the following data encapsulation steps: 1. The layer 3 header is added to the data before being passed on the next layer. 2. A header is added to previous data and is passed to the Internet layer. 3. A trailer, usually the frame check sequence of FCS, and a header are added. 4. An application sends user data. A. 4, 3, 2, 1 B. 1, 2, 3, 4 C. 4, 2, 1, 3 D. 3, 4, 2, 1 What OSPF features have been updated for IPv6? (Choose two) A. It uses a 64-bit number instead of an Internet Protocol version 4, or IPv4 address for the router ID B. Enabled per-link, not per-network C. Adjacencies and next-hop attributes use the router ID as global addresses D. IPv6 is used for transport of the link-state advertisement, or LSA https://www.learncisco.net/courses/icnd-1/introducing-ipv6/configuring-ospfv3.html Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. What is the name of the firewall feature that, when used, can maintain a historical database of each connection through a device: Where it was sourced, destined, and which protocol and protocol port it was using? A. Stateless Inspection B. Stateful Inspection C. Network Protocol Analysis D. Protocol State Analysis Which problems can manifest in a redundant switched topology? (Choose three) A. Media Access Control, or MAC, database instability B. Virtual LAN, or VLAN, mismatch errors C. Broadcast storms D. Multiple frame transmission E. Trunk ports failing establishment https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/redundant-topologies.html What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 Which command is used to ensure that a switch interface will never become a trunk and remain a member of a single VLAN? A. Switchport mode trunk B. Switchport mode access C. Switchport nonegotiate D. Switchport access vlan vlan-number E. Switchport trunk encapsulation dot1q Which of the following commands displays the enabled OSPFv3 interfaces, along with the adjacent OSPF neighbors connected to them? A. show ipv6 ospf neighbor B. show ipv6 ospf C. show ipv6 route ospf D. show ipv6 ospf interface https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/ospfv3-configuration.html Which is true in a spine-leaf architecture? (Choose two) A. Each leaf switch must connect to every spine switch. B. Each leaf switch must connect to one spine switch. C. Each spine switch must connect to every leaf switch. D. Each spine switch must connect to one leaf switch. Where is the Cisco IOS stored on a Cisco IOS ISR Router? A. CPU B. Flash C. RAM D. NVRAM E. ROM In Software-Defined Access (SDA), which of the answers are part of the overlay data plane? A. LISP B. GRE C. OSPF D. VXLAN What command will successfully change the configuration register so that a Cisco IOS 2900 series router will boot into ROM Monitor mode? A. Config-register 0x2104 B. Config-register 0x2105 C. Config-register 0x2101 D. Config-register 0x2102 E. Config-register 0x2120 F. Config-register 0x2103 G. Config-register 0x2106 Which of the following describes a Private IPv6 address? A. ::1 B. Starts with FE80::/10 C. Represented by :: D. Starts with 2000::/3 https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/ipv6-unicast-addresses.html The IPv6 address “2001:db8:abc:1234:0290:27ff:fe17:fc0f/64“ is assigned to a device. How was the interface portion assigned? A. Manually, using DHCPv6 B. Dynamically, using a random generator C. Manually by an administrator D. Dynamically, using EUI-64 You are implementing a VLSM network. You are using the Class B network of 172.16.0.0/16 and need to create 256 networks from this. The fifth network will then be subnetted into /30 networks. What is the subnet ID of the fourth /30 network? A. 172.16.4.12/30 B. 172.16.4.4/30 C. 172.16.4.6/30 D. 172.16.4.8/30 E. 172.16.4.14/30 F. 172.16.4.10/30 An engineer connects to Router R1 and issues a show ip ospf neighbor command. The status of neighbor 2.2.2.2 lists FULL/BDR. What does the BDR mean? A. R1 is an Area Border Router. B. R1 is a backup designated router. C. Router 2.2.2.2 is an Area Border Router. D. Router 2.2.2.2 is a backup designated router. What is the name of the protocol that is used by IEEE 802.1x devices to communicate with the authenticator and authentication server? A. EAP B. EAPoL C. RADIUS D. TACACS+ Network device addresses use binary system to define their location on the network. How do the decimal and binary number systems work? (Choose three) A. Mathematics is based on the binary system B. Computers are based on the decimal system C. When performing powers of 2 calculations, the least significant bit is equal to 2^1 D. In the decimal system, the digits are 0,1, 2, 3, 4, 5, 6, 7, 8, and 9 E. Powers of 2 provide the basis for binary values F. The binary system uses only the digits 0 and 1 Which statement describes how to create VLANs? A. Use the [vian interface] command B. Use the [vlan] global configuration command C. Use the [switchport vlan name] command https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/vlan-operations.html An enterprise plans to start using a public cloud service and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Which DSCP Assured Forwarding value provides the worst drop and worst queue performance? A. AF41 B. AF43 C. AF11 D. AF13 You are using CDP to build a network topology. Which command is used to verify the IPv4 address of the neighboring Cisco IOS device? A. show interfaces B. show cdp C. show ip interfaces D. show cdp neighbors E. show cdp neighbors detail F. show ip interface brief Which command is used to display the open ports on a router so that you can determine which services should be disabled? A. show ports open host B. show control-plane host open-ports C. show flash D. show file system What are the valid encapsulation methods when forcing a device to become a trunk port? (Choose three) A. private-vlan B. dot1q-tunnel C. dot1q D. negotiate E. isl Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 What are some of the wireless LAN controller (WLC) capabilities? A. Security management B. Dynamic RF management to assign channels to APs C. RF monitoring to gather information about the channel D. Ease of deployment by programming all RF policies and wireless LAN policies on all APs E. All of these are correct. Packets are able to take two different paths across the network to their destination. The first path has a 10 Mbps link, a 5 Mbps link, and a 100 Mbps link. The second path uses a 2 Mbps link and a 100Mbps link. What is the cost of the path the packets will take? A. 31 B. 51 C. 20 D. 11 https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/ospf-data-overview.html A queuing system has three queues serviced with round robin scheduling and one low latency queue that holds all voice traffic. Round robin queue 1 holds predominantly UDP traffic, while round robin queues 2 and 3 hold predominantly TCP traffic. The packets in each queue happen to have a variety of DSCP markings per the QoS design. In which queues would it make sense to use a congestion avoidance (drop management) tool? (Choose two) A. The LLQ B. Queue 1 C. Queue 2 D. Queue 3 Which hash method is used by default when using the enable secret Cisco IOS command? A. 3DES B. MD5 C. SHA-0 D. HMAC Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands Which command will assign a global IPv6 address with an autoconfigured interface portion to a router interface? A. ipv6 address 2001:db8:1:1::0001/64 eui-64 B. ipv6 address 2001:db8:1:1::0001/64 auto-configure C. ipv6 address 2001:db8:1:1::/64 auto-configure D. ipv6 address 2001:db8:1:1::/64 eui-64 E. ipv6 address 2001:db8:1:1::/64 Refer to the diagram. What is the official name of the network (Network A) that is broadcast by an AP? A. SSID B. BSS C. ESS D. SRDID Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture What is the default security violation mode for port security on a Cisco 2960 Catalyst switch? A. Disable B. Shutdown C. Protect D. None E. Restrict F. Err-disable Using the exhibit as a reference, how many JSON objects are there? A. 11 B. 1 C. 2 D. 12 Which statements describe how to configure and verify basic NTP protocol? (Choose two) A. To configure an NTP master clock, execute commands in the global configuration mode B. Commands should be executed in the user EXEC mode when displaying the status of NTP C. When verifying the status of NTP associations, commands should be executed in the user EXEC mode D. Configuring a higher stratum value indicates a higher priority https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html The show port-security interface f0/1 command lists a port status of Secure-shutdown. Which of the following answer must be true about this interface at this time? A. The show interface status command lists the interface status as connected. B. The show interface status command lists the interface status as err-disabled. C. The show port-security interface command could list a mode of shutdown or restrict, but not protect. D. The show port-security interface command could list a violation counter value of 10. Robust wireless encryption is based on which of the following algorithms? A. WEP B. AES C. DES D. IPsec Which of the following commands will display the general status of the EtherChannel interface? A. show etherchannel summary B. show interface port-channel C. show etherchannel port-channel https://www.learncisco.net/courses/icnd-2/etherchannel-and-l3-redundancy/configuring-etherchannel.html Which of the following commands will display one line of information per port channel? A. show etherchannel summary B. show interface port-channel C. show etherchannel port-channel https://www.learncisco.net/courses/icnd-2/etherchannel-and-l3-redundancy/configuring-etherchannel.html Which switch ”show” command is used to display the IP address, subnet mask and default gateway settings? A. show version B. show interfaces C. show running-config https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html Which of the following behaviors are applied to a low latency queue in a Cisco router or switch? (Choose two) A. Shaping B. Policing C. Priority scheduling D. Round-robin scheduling Which option is not one of the most commonly deployed virtualization vendors and products? A. Oracle XenSpace B. Microsoft Hyper-V C. VMware vCenter D. Red Hat KVM Which of the following protocols are used to auto negotiate trunk formation between two switches? A. CDP B. VTP C. DTP D. STP Which of the following components contains the running copy of the configuration file? A. Interface B. ROM C. Flash D. RAM E. CPU F. NVRAM https://www.learncisco.net/courses/icnd-2/network-management/router-internal-components-overview.html Which command enables IPv6 forwarding on a Cisco router? A. ipv6 local B. ipv6 host C. ipv6 unicast-routing D. ipv6 neighbor https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-connectivity.html Which QoS feature is typically used outbound to an ISP to reduce the amount of traffic that is dropped by exceeding the purchased rate? A. Traffic shaping B. Traffic policing C. Traffic limiting D. Traffic classification What are considerations when troubleshooting ACL issues? (Choose two) A. They use top-down processing with immediate execution upon a match B. They use bottom-up processing with immediate execution upon a match C. If you don't match anything in the ACL, there is an implicit denial at the end D. Outbound ACLs affect the dynamic routing protocol In the virtualization world, the ___________ manages and allocates the host hardware for each VM. A. Host controller B. Hyperthreader C. Hypervisor D. Host service

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources